+1-415-467-3400

Separator

48 Item(s)

per page

Set Descending Direction
  1. Filter, Separator, Puroflux, PF-64, 150 PSI, 10 HP

    Stock Number: S740013

    Puroflux separator model PF61-040, 4" flanges (inlet and outlet), 10 hp pump motor, 330 gpm, purge connection is 1-1/2" ftp, 150 PSI. Unit removes particulate as low as 45 microns.
  2. Filter, Separator, Puroflux, PF-64, 150 PSI, 10 HP

    Motor, 3 HP, Stainless Motor Inc, Inline, Unused

    Stock Number: S740153

    Unused Inline Planetary Gearmotor stainless steel manufactured by Stainless Motor Inc., cast T304 housing with sanitary foot mounts, 3 hp, 208/230/460 volt, 1760 rpm, 3 phase, with gear ratio of 3.67:1.
  3. Motor, 3 HP, Stainless Motor Inc, Inline, Unused

    Separator, Air Classifier, 12", Donaldson, A-12,

    Stock Number: S736073

    Laboratory size mechanical air separator, Majac-Donaldson model A-12 Acucut, 12" diameter with 1 HP vari-speed rotor drive, (500 to 5500 rpm). Designed for very fine particle separation cuts involving material in the 1/2 to 35 micron range. Includes feeder, powder recovery system, 7.5 HP (90 CFM @ 10" hg) primary air blower, and controls. Rated from 1-20 lbs/hr. No nameplate on this unit (Sister unit was Serial# 12-12090). Last use in pharmaceutical processing.
  4. Separator, Air Classifier, 12", Donaldson, A-12,

    Separator, Air Classifier, 12", Donaldson, Sub-micron,

    Stock Number: S670612

    Laboratory size mechanical air separator, Majac-Donaldson model A12 Acucut, 12" diameter with 1 HP vari-speed rotor drive (500 to 5500 rpm). Designed for very fine particle separation cuts involving material in the 1/2 to 35 micron range. Includes feeder, powder recovery system, 7.5 HP (90 CFM @ 10" hg) primary air blower, and controls. Rated from 1-20 lbs per hr. Run on 460 VAC + compressed air. Serial number 12-12087.
  5. Separator, Air Classifier, 12", Donaldson, Sub-micron,

    Separator, Air Classifier, 5'4", Hosokawa, Whizzer, (2)

    Stock Number: C738677

    (2) Air separator, single Whizzer separator, measures 64" diameter x 72" straight side, plus 78" cone bottom, inlet measures 32" x 39", outlet measures 15" x 82", Whizzer blades driven by 30 HP motor, vari-speed. Designed to be used with hosokawa air swept hammer mill. Unused.
  6. Separator, Air Classifier, 5'4", Hosokawa, Whizzer, (2)

    Separator, Air Classifier, 8'4", Raymond Static Classifier,

    Stock Number: A735932

    Separator, Raymond 66" diameter static classifier, last used with a 66" diameter Raymond roller mill for classification of coal fines. Not a double Whizzer separator. It has static veins that are electrically adjustable with controls. Used for 400 hours only. Dismantled and ready to ship. Condition excellent. Raymond serial number 77124, drawing number D-GR-2814-0.
  7. Separator, Air Classifier, 8'4", Raymond Static Classifier,

    Separator, Cross Flow, 3' X 3', Eriez, 201-102-000,

    Stock Number: C740614

    Eriez cross flow separator, 3' X 3', high capacity teeter bed, style 201-102-000, serial number 232330-1 and 2, complete with control panel and automatic values, carbon steel tank, (6) 1.5" magnetic rods, new in 2010 and in excellent condition. For separation of materials in controlled water column.
  8. Separator, Cross Flow, 3' X 3', Eriez, 201-102-000,

    Separator, Cyclone, 10" x 10", S/st, Air,

    Stock Number: S740140

    Cyclone air separator with stainless steel contact parts, 10" diameter x 10" straight side with 14" cone bottom to 4"discharge. Unit has 2" diameter air inlet and 3" diameter top outlet.
  9. Separator, Cyclone, 10" x 10", S/st, Air,

    Separator, Cyclone, 17" x 20", S/st, Air, 45 Deg cone

    Stock Number: S740133

    Cyclone air separator with stainless steel contact parts, 17" diameter x 20" straight side with 45" cone bottom to 6"x6 square discharge. Unit has 6" diameter air inlet and 8" diameter top outlet.
  10. Separator, Cyclone, 17" x 20", S/st, Air, 45 Deg cone

    Separator, Cyclone, 18" X 2', S/st, Semco, (3)

    Stock Number: S674540

    (3) Cyclone separator, manufactured by Semco, stainless steel, 18" diameter x 2' straight side with approx. 70 deg. cone to 9" diameter product discharge. Unit features 4" diameter infeed, 5" air discharge. Cyclone complete with (2) pneumatic vibrators, inlet and discharge butterfly valves.
  11. Separator, Cyclone, 18" X 2', S/st, Semco, (3)

    Separator, Cyclone, 24" X 24", C/st,

    Stock Number: C739302

    Cyclone, 24" X 42" straight side. Unit has a 36" cone. 14" diameter bottom outlet as well as 10" diameter center opening and 6" diameter top feed. Manufactured by Idaho Steel. Unit is lug-mounted.
  12. Separator, Cyclone, 24" X 24", C/st,

    Separator, Cyclone, 28" X 36", C/st, (6)

    Stock Number: C739301

    (6) Cyclone, 28" diameter X 36" straight side. Unit has a 9" diameter center opening.
  13. Separator, Cyclone, 28" X 36", C/st, (6)

    Separator, Cyclone, 48" X 10'4", C/st, Air, 76" Cone,

    Stock Number: S737334

    Cyclone air separator with carbon steel contact parts, 48" diameter x 28" straight side with 76" cone bottom to 9" diameter discharge. Unit has 15" x 6" air inlet with flange and 19" diameter top outlet with flange. Overall height is 10' 7", overall diameter is 60". Unit previously suspended from overhead with 1/2" rod hangers. Good condition.
  14. Separator, Cyclone, 48" X 10'4", C/st, Air, 76" Cone,

    Separator, Cyclone, 54" X 9', S/st, Air, 6'10" Cone, 10" Disc

    Stock Number: S737333

    Cyclone air separator with stainless steel contact parts, 54" diameter x 26" straight side with 82" cone bottom to 10" diameter discharge. Unit has 9" diameter to 18" x 10" air inlet with flange and 20" diameter top outlet with flange. Overall height is 10' 5", overall width is 75". Unit previously suspended from overhead with 1/2" rod hangers. Good condition.
  15. Separator, Cyclone, 54" X 9', S/st, Air, 6'10" Cone, 10" Disc

    Separator, Cyclone, 60" X 120", C/st, Air,

    Stock Number: S740944

    Cyclone air separator, all carbon steel construction. Chamber measures 60" diameter X 36" straight side with 85" cone bottom. Includes 18" diameter inlet and 8" diameter discharge outlet. Mounted on mild steel frame. Fair condition.
  16. Separator, Cyclone, 60" X 120", C/st, Air,

    Separator, Cyclone, Air, 21” X 48”, S/st, Rotary Valve, (2)

    Stock Number: S740525

    (2) Stainless steel cyclone with rotary airlock valve. Cyclone is manufactured by Premier Pneumatics, model 59781-1, measures 21" diameter X 48" high, leading to Nucon model# DT 500 DEM rotary airlock valve, stainless steel, 10" diameter, driven by 1/2 HP motor. Previously used at food processing facility and in good condition.
  17. Separator, Cyclone, Air, 21” X 48”, S/st, Rotary Valve, (2)

    Separator, Cyclone, Air, 30" X 78", S/st, 44" Cone, MAC

    Stock Number: S740407

    Cyclone air separator, stainless steel contacts. Unit is manufactured by MAC, model number CT30, serial number 97-CCT-05-007. Unit measures 30" diameter X 28" straight side with 44" cone bottom. 14" diameter inlet and 12" diameter discharge. Includes side access door. Good condition.
  18. Separator, Cyclone, Air, 30" X 78", S/st, 44" Cone, MAC

    Separator, Cyclone, Air, S/St, 18" X 16", 4" Inlet

    Stock Number: S740151

    Cyclone air separator with stainless steel contact parts, 18" diameter x 16" straight side with 65" cone bottom to 10"discharge. Unit has 4" diameter air inlet and 4" diameter top outlet.
  19. Separator, Cyclone, Air, S/St, 18" X 16", 4" Inlet

    Separator, Cyclone, S/st, Air, 24" x 28", 3" Inlet

    Stock Number: S740152

    Cyclone air separator with stainless steel contact parts, 24" diameter x 28" straight side with 18" cone bottom to 4"discharge. Unit has (2)3" diameter air inlets and 3" diameter top outlet.
  20. Separator, Cyclone, S/st, Air, 24" x 28", 3" Inlet

    Separator, Grit Removal, 7', S/st, Eutek Systems, Teacup,

    Stock Number: S737234

    Separator, 7' diameter, stainless steel construction, manufactured by Eutek systems, Teacup design, grit removal and washing, Model number 8/103/07, measures 7' diameter x 57" straight side, plus dished bottom, leading to 30" diameter cone shaped discharge, 3" diameter outlet. Includes approx. 30" diameter center top opening, 6" diameter side inlet and overflow outlet. Good condition.
  21. Separator, Grit Removal, 7', S/st, Eutek Systems, Teacup,

    Separator, Hydrocyclone (3), Krebs, D15, Ceramic,

    Stock Number: S740705

    Krebs Hydrocyclone pod, including (3) Krebs hydrocyclones, model D15LB-105-T123, Ceramic Lined. Mounted and piped together on stand with distrubtion tank, techniquip kinfegate valves, and ceramic lined launder. Condition excellent. Last used on coal fines.
  22. Separator, Hydrocyclone (3), Krebs, D15, Ceramic,

    Separator, Hydrocyclone, Krebs, 10", R/L, D-10B

    Stock Number: S734159

    Separator, hydrocyclone, Krebs 10" diameter, model number D-10B-840, rubber lined, with some fittings. Good condition.
  23. Separator, Hydrocyclone, Krebs, 10", R/L, D-10B

    Separator, Hydrocyclone, Krebs, 15", DS15LB, Pod of 4, (2)

    Stock Number: S738512

    (2) Krebs hydrocyclone, pod of (4) cyclones, Krebs model number DS15LB-10. 5-2152, rubber-lined, 8" overflow, 6" inlet. Includes overflow and underflow launders used with radial manifolded hydrocyclones. Cyclones include inlet head liner, size 4.5" vortex finder, size 3.5" apex orifice. Previously used at phosphate minerals processing plant. Includes hydraulic valves for each hydrocyclone. Previously used at phosphate minerals processing plant.
  24. Separator, Hydrocyclone, Krebs, 15", DS15LB, Pod of 4, (2)

    Separator, Hydrocyclone, Krebs, 26", Rubber-lined, D26B,

    Stock Number: S738508

    Krebs hydrocyclone, model D26B-1085, rubber-lined, 26" diameter, 12" diameter overflow, 10" diameter inlet, includes inlet head liner, size 8" vortex finder, size 5-1/4" apex orifice. Previously used at phosphate minerals processing plant. Equipment was dismantled and is now being stored at crane yard for easy loading.
  25. Separator, Hydrocyclone, Krebs, 26", Rubber-lined, D26B,

    Separator, Magnet, Indsutrial Magnetics, Flo-tHRu, 6",

    Stock Number: S674750

    Block magnet, flo-thru (in line) type, manufactured by Indsutrial Magnetics Inc. Model number C15-1-027, with 6" in and out connections (one round and one square). Appears to be in good condition.
  26. Separator, Magnet, Indsutrial Magnetics, Flo-tHRu, 6",

    Separator, Magnetic, 15" X 36", C/st, Eriez, Drum,

    Stock Number: S741073

    Eriez drum magnetic separator, model number 15 X 36 RE D.1.4. Drum measures 15" diameter X 36" long with hinged lid and 5" top opening. Includes Eriez vibratory mechanism model 55A, Style 26. Driven by 3/4HP, 230/460V, 1725 RPM, 3/60Hz motor. Complete with controls. Previously used in conjunction with vibratory feeder, stock number S741071.
  27. Separator, Magnetic, 15" X 36", C/st, Eriez, Drum,

    Separator, Magnetic, 3", S/st, Liquid, MPI,

    Stock Number: S741224

    Magnetic Products Inc. (MPI) triple rod screener, magnetic separator for liquids. Includes 3" diameter sanitary tri-clamp inlet leading to magnetic bars, with 3" diameter discharge on side bottom of housing, stainless steel construction, includes 1-1/2" diameter bottom outlet with manual valve. Last used at food processing facility.
  28. Separator, Magnetic, 3", S/st, Liquid, MPI,

    Separator, Magnetic, 3", S/st, Liquid, MPI, TW-3,

    Stock Number: S741225

    Magnetic Products Inc. (MPI) triple rod screener, magnetic separator for liquids, model number TW-3-REN-S. Includes 3" diameter flanged inlet leading to magnetic bars, with 3" diameter flanged discharge on side bottom of housing, stainless steel construction, includes 1-1/2" diameter bottom outlet with manual valve. Last used at food processing facility.
  29. Separator, Magnetic, 3", S/st, Liquid, MPI, TW-3,

    Separator, Magnetic, 36" X 120", S/st, Eriez, Drum (2)

    Stock Number: S737554

    (2) Eriez magnetic separators, 36" diameter x 120" long, stainless steel, dry drum type. Never used. Each complete with 30 HP, vari-drive thru chain and sprocket. Permanent magnets, style number 7119, Serial number 55306. Tested with good strength. Each drum is fed with Eriez vibratory feeder, model number 80B, Serial number Z11-357. 120" wide with three vibrators, stand and controller. Rated at 50 to 120 tons per hour depending on material. Each unit is rated at approximately 950 gauss at 2 inches from the drum surface, and approximately 2,000 gauss on the drum surface. New 1980, never installed.
  30. Separator, Magnetic, 36" X 120", S/st, Eriez, Drum (2)

    Separator, Magnetic, 36" X 36", Eriez Drum, S/st

    Stock Number: S737555

    Eriez magnetic separator, 36" diameter x 36" long, stainless steel, dry drum type, never used. Complete with 10 HP vari-drive with chain and sprocket. On stand with feed hopper, Eriez vibratory feeder with controller, and discharge chutes. Rated at 15 to 40 tons per hour depending on material. New 1980, never installed. Serial number 55306 model MKS.
  31. Separator, Magnetic, 36" X 36", Eriez Drum, S/st

    Separator, Magnetic, 36" X 96", S/st, Eriez, Drum, (3)

    Stock Number: S738514

    (3) Magnetic drum separator, 36" diameter x 96" face, manufactured by Eriez Magnetics, includes stainless steel drum, driven by 5 HP SEW-Eurodrive, 330/575 volt, 3/60Hz, includes top mounted spray bar/nozzles along back of drum, protective framing and access stairs. Rated for 2000 Gauss on surface @ 960 GPM. Previously used at phosphate minerals processing facility. Equipment was dismantled and is now being stored at crane yard for easy loading.
  32. Separator, Magnetic, 36" X 96", S/st, Eriez, Drum, (3)

    Separator, Magnetic, Eriez, Drum, 12" x 7", Mdl L-8,

    Stock Number: C741160

    Eriez magnetic drum separator, 12" diameter X 7" face, model number L-8 WET DRUM, style C-1N-661137, DC Hertz, serial number 306672, 3.21 Amps. Unitized on mild steel frame with stainless steel encasing. Drum us driven by 0.33 HP, 115/230V, 1725 RPM, 3/60 HZ motor through gear reducer and v-belt or chain & sprocket assembly. Complete with Eriez magnetic digital controller. Very good condition.
  33. Separator, Magnetic, Eriez, Drum, 12" x 7", Mdl L-8,

    Separator, Magnetic, Flow-Thru, Liquid, 1/2",

    Stock Number: S741209

    Stainless steel magnetic separator, flow-through type, 1-1/2" diameter flange inlet, stainless steel construction. Includes manual valve. Previously used in food manufacturing facility. Typically used for liquids and slurries.
  34. Separator, Magnetic, Flow-Thru, Liquid, 1/2",

    Separator, Magnetic, Flow-Thru, Liquid, 3",

    Stock Number: S741208

    Stainless steel magnetic separator, 3" diameter in/out, flanged openings. Manufactured by Eriez, Ferrous trap, model B-3, includes clamp side for internal magnetic bars. Last used in food processing facility. Typically used for liquids and slurries.
  35. Separator, Magnetic, Flow-Thru, Liquid, 3",

    Separator, Magnetic, Flow-Thru, Liquid, S/st, 1", (2)

    Stock Number: S741207

    (2) Stainless steel flow through magnetic separators, 1" diameter In/out, stainless steel, includes manual valve for outlet. Typically used for liquids and slurries.
  36. Separator, Magnetic, Flow-Thru, Liquid, S/st, 1", (2)

    Separator, Magnetic, Outotec, Belt, 64", 3-Deck

    Stock Number: C740616

    Outotec magnetic separator, belt type, with magnetic rolls, triple stage, model HE-10-150, serial number 07-340-3. Dry mass: 1600 kg, capacity of 6 tons per hour. Belt measures 64" wide, 3-deck, 80 degrees Celsius maximum temperature, complete with spare unused belt, feeder, control panel, new in 2007 and in excellent condition.
  37. Separator, Magnetic, Outotec, Belt, 64", 3-Deck

    Separator, Magnetic, Pneumatic, 5", S/st, Cartridge, (3)

    Stock Number: S741227

    (3) Eriez magnetic separator, 6" diameter in/out, cartridge separator for pneumatically conveyed dry material. Model number 5IN. RE RF Cartridge Magnet, style 9943967 (serial number 143412), style 9947447 (serial number 146857) & style 9943967 (serial number 149766). Product flows around solid stainless cone and over magnetic cartridge. Housing is all stainless steel construction. Previously used at food processing facility.
  38. Separator, Magnetic, Pneumatic, 5", S/st, Cartridge, (3)

    Separator, Magnetic, Pneumatic, 6", S/st, Eriez, (2)

    Stock Number: S741226

    (2) Eriez magnetic separator, 6" diameter in/out, cartridge separator for pneumatically conveyed dry material, model 16IN. RE RF Cartridge Magnet, style 960-9960. Product flows around solid stainless cone and over magnetic cartridge. Housing is all stainless steel construction. Serial number 147903. (One is less nameplate). Previously used at food processing facility.
  39. Separator, Magnetic, Pneumatic, 6", S/st, Eriez, (2)

    Separator, Magnetic, Pneumatic, 6", S/st, Eriez, Pipe

    Stock Number: S741275

    Stainless steel permanent magnet, round pipe magnetic separator, round, manufactured by Magnetic Products Inc (MPI). Magnet is mounted on side of stainless steel housing, 6" diameter in & out. Model number NP-R207-SS-304-S, shop order number 22415, work order number 28650, New in 2011. Used to remove metals from gravity or pneumatically conveyed dry, free flowing products. Last used at food processing facility.
  40. Separator, Magnetic, Pneumatic, 6", S/st, Eriez, Pipe

    Separator, Magnetic, Pneumatic, 6", S/st, Magnetic Hump

    Stock Number: S741274

    Stainless steel permanent magnet with magnetic hump, manufactured by Eriez. Magnet is mounted on side of stainless steel housing, 6" diameter in & out. Used to remove metals from pneumatically conveyed dry, free flowing products. Previously used in food processing facility
  41. Separator, Magnetic, Pneumatic, 6", S/st, Magnetic Hump

    Separator, Magnetic, Pneumatic, 6", S/st, Round Pipe

    Stock Number: S741273

    Stainless steel permanent magnet, 6" diameter in & out, round pipe magnetic separator, manufactured by Eriez. Magnet is mounted on side of stainless steel housing. Used to remove metals from gravity or pneumatically conveyed dry, free flowing products. This assembly is installed by cutting out the section where magnetic protection is required and slipping the separator into position. Previously used in food processing facility.
  42. Separator, Magnetic, Pneumatic, 6", S/st, Round Pipe

    Separator, Magnetic, Pneumatic, 8", S/st, Magnetic Hump

    Stock Number: S741272

    Stainless steel permanent magnet with magnetic hump, manufactured by Cesco. Magnet is mounted on side of stainless steel housing, 8" diameter flanged opening on one end, and 10" x 10" flanged opening on other side. Used to remove metals from gravity or pneumatically conveyed dry, free flowing products. Previously used in food processing facility.
  43. Separator, Magnetic, Pneumatic, 8", S/st, Magnetic Hump

    Separator, Magnetic, Pneumatic, S/st, MPI, 5",

    Stock Number: S741211

    Magnetic separator, Pneumatic Line Magnet, manufactured by Magnetic Products Inc., model number PLM-5-REN-QC-304, shop order number 22354, work order number 28581, 5" diameter in/out. Includes quick-clean removable magnet element, 4" diameter X 12" long, through center of stainless housing. Typical applications include powder or granular food products, pharmaceuticals, plastics and chemicals conveyed at high speeds in low density, high-air systems. Can be run vertically or horizontally. New in 2012. Good condition.
  44. Separator, Magnetic, Pneumatic, S/st, MPI, 5",

    Separator, Magnetic, Pneumatic, S/st, MPI, Mdl PLM-5,

    Stock Number: S741200

    Magnetic separator, Pneumatic Line Magnet, manufactured by Magnetic Products Inc., model number PLM-5-REN-QC, serial number 14045/HOT, 4" diameter in/out. Includes quick-clean removable magnet element, 4" diameter X 12" long heavy duty cartridge magnet running through center of stainless housing. Typical applications include powder or granular food products, pharmaceuticals, plastics and chemicals conveyed at high speeds in low density, high-air systems. Can be run vertically or horizontally. Good condition.
  45. Separator, Magnetic, Pneumatic, S/st, MPI, Mdl PLM-5,

    Separator, Magnetic, Pneumatic, S/st, MPI, Plate,

    Stock Number: S741223

    Magnetic Products Inc. (MPI) inline pneumatic plate magnet, stainless steel magnetic separator, 2-3/4" in/out, model number LLNP-R207-S. Includes magnetic section on door and center of housing, stainless steel construction. Last used in food processing facility.
  46. Separator, Magnetic, Pneumatic, S/st, MPI, Plate,

    Separator, Magnetic, Rotary, Ferris Wheel, 3/4 HP, C/st,

    Stock Number: S732029

    Rotary ferris wheel type magnet with 17" x 24" flanged feed inlet, carbon steel contact parts. Unit has stainless steel ferris wheel type magnet assm with 16" long magnets inside 1" diameter stainless steel pipes, total of 16 magnets on rotating assembly. Unit driven by 3/4 HP tefc, 220/440V gearhead motor drive. carbon steel housing measures 21" x 28" with 2" flange x 31" overall height. Unit in very good condition, complete with removable inspection cover. Last used in bakery ingredient blend factory for trapping metals in flour feed system.
  47. Separator, Magnetic, Rotary, Ferris Wheel, 3/4 HP, C/st,

    Separator, Magnetic, WHIMS, Mdl CF-1005

    Stock Number: A738169

    Eriez magnetic separator, WHIMS Model CF-1005. Used for six month only on industrial minerals. All skid mounted with controls and electricals rated at 8,000 gauss, 32 kW 49" diameter ring, variable speed drive with 5 HP motor. New in 1988.
  48. Separator, Magnetic, WHIMS, Mdl CF-1005

    Separator, Press, Screw, (5) 6" X 24" Barrels, S/st,

    Stock Number: S736867

    Separator / extractor, consists of (5) 6" diameter x 24" long barrels with internal screws and tapered screens, each barrel has 1-1/2" diameter Feed inlet, leading to pressing section, product is squeezed by screw through tapered screw & screen, 3-1/2" diameter On feed end and 2" diameter On discharge end. Solids discharge thru 3" diameter outlets with valve controlled by tension springs and includes 1-1/2" diameter liquid discharge with manual ball valve & internconnecting piping. Each screw is driven by independent. 75kw (1 HP) 220V, 1720 RPM, 60Hz motors. Includes inline heater (small shell & tube heat exchanger), which feeds liquid to each barrel through 1-1/2" diameter Inlet. Manufactured by Sato & Company. Previously used in a tofu manufacturing facility as a soy bean separator. Complete with main control panel which operated both extractors. Good condition.

48 Item(s)

per page

Set Descending Direction

Please wait...