+1-415-467-3400

Crusher

24 Item(s)

per page

Set Descending Direction
  1. Crusher, Cone, Allis Chalmers, 36", Hydrocone, Mdl 7-36,

    Stock Number: C740404

    Allis Chalmers cone crusher, Model 7-36 Hydrocone. Driven by 60 HP (approximately) motor and includes hydraulics and switch gear, New in 1968. Previously used on soft limestone.
  2. Crusher, Cone, Allis Chalmers, 36", Hydrocone, Mdl 7-36,

    Crusher, Cone, Braun, Lab, "coffee Mill", 6" Diameter,

    Stock Number: S243798

    Cone crusher, lab size Braun sample crusher, "coffee mill", 6" diameter, mounted on stand, adjustable crush size, less motor.
  3. Crusher, Cone, Braun, Lab, "coffee Mill", 6" Diameter,

    Crusher, Cone, Kue Ken, 51", Mdl 51 CT, (2)

    Stock Number: D737893

    (2) Cone crusher, manufactured by Kue Ken, 51" diameter, Model number 51 CT.
  4. Crusher, Cone, Kue Ken, 51", Mdl 51 CT, (2)

    Crusher, Cone, Nordberg, Mdl WF-800, 800 HP,

    Stock Number: D738314

    Cone crusher, manufactured by Nordberg, Model# WF-800, driven by toshiba 800 HP, 4000 volt, 1180 RPM, 3-phase induction motor. Water flush cone crusher.
  5. Crusher, Cone, Nordberg, Mdl WF-800, 800 HP,

    Crusher, Cone, Symons, 7', HD, 400 HP,

    Stock Number: D735898

    Cone crusher, Symons Nordberg, 7' shorthead, heavy duty. driven by 400 HP, 460 volt, 3 phase, 60 Hz motor. Includes lube sets, hydraulic couplings, unused housings, unused oil tank heater, unused filters. Spare parts available.
  6. Crusher, Cone, Symons, 7', HD, 400 HP,

    Crusher, Cone, Symons, Mdl 4800, Sh, 125 HP Motor,

    Stock Number: C242375

    Cone crusher, Symons 4800, configured as a short head for fine crushing. Serial number 42040. In addition to normal spring cluster mecanism for tramp iron protection, crusher has hand operated hydraulic system for bowl adjustments & cleaning. Crusher has 125 HP motor and V-belt drive. Includes integral lube pump & external reservoir tank.
  7. Crusher, Cone, Symons, Mdl 4800, Sh, 125 HP Motor,

    CRUSHER, GYRATORY, 30" X 60", NORDBERG, 250 HP,

    Stock Number: D735896

    Gyratory crusher, 30" x 60", manufactured by Nordberg, Model 30-6-GY-554. Driven by 250 HP, 1187 RPM, frame A509Z, 292 amps, 3-phase, 60 Hz motor. 450 RPM countershaft speed. Has a 30" feed opening, 4-1/2" open side setting, 1" eccentric throw. Lube motor attached, 10 HP. Completely rebuilt in 1998 including new eccentric, pinion, and all electrical gear. Complete rebuild of counter shaft box, including all new bushings, step plates, spider assembly, and cap. Unit shut down in 1999 and retrofitted by Nordberg with hydraulic adjustment from underneath the crusher.
  8. CRUSHER, GYRATORY, 30" X 60", NORDBERG, 250 HP,

    Crusher, Gyratory, 48 X 74, Allis Chalmers, Kobe,

    Stock Number: D737395

    Gyratory crusher, 48" x 74", manufactured by Kobe/Allis Chalmers, Model# 48-74, previously used to crush limestone. Offered with hydraulic oil tank and accumulator. (less motor) previously used with 300 kW drive. Good condition.
  9. Crusher, Gyratory, 48 X 74, Allis Chalmers, Kobe,

    Crusher, Gyratory, 54" X 74", Traylor, 450 HP,

    Stock Number: D735894

    Gyratory crusher, 54" x 74", manufactured by Traylor, type INTIN. Driven by 450 HP, 4000v motor with starter and air cooling system. Currently disassembled, matchmarked and pressure washed. Last operated in 2003 crushing limestone. reported to be in good condition. Complete.
  10. Crusher, Gyratory, 54" X 74", Traylor, 450 HP,

    Crusher, Gyratory, 60" X 89", Allis Chalmers

    Stock Number: D735906

    Gyratory crusher, 60" x 89", manufactured by Allis Chalmers. 48" maximum feed size. Includes straight bottom shell design, lower top shell, top shell section, spider, spider arm liners, arm guards, concaves, mainshaft, mainshaft lower journal, hydroset, 60- 89 eccentric. Bottom shell bushing, eccentric support plates, pinion shaft-countershaft assembly. Less motor. Spares available.
  11. Crusher, Gyratory, 60" X 89", Allis Chalmers

    Crusher, Impact, 1000 HP, 60" X 80", Williams, Reversible,

    Stock Number: S248250

    Williams reversible impact crusher, 60" diameter x 80" long rotor, swing type sledge hammers. Williams model number K, type 680. Previously had 1000 HP, 4000 volt, 712 RPM, 3-phase, 60Hz AC motor. Feed opening 27" x 80", rated at 1000 tons per hour on limestone, last used as secondary crusher. Unit is equipped with hydraulic opening mechanism to split chamber and change out parts. Unused hammers (16 approx. hammers) also available. Serial number 15257.
  12. Crusher, Impact, 1000 HP, 60" X 80", Williams, Reversible,

    Crusher, Impact, Horizontal, Penn, Mdl CAL11-44

    Stock Number: S738948

    Pennsylvania reversible impact crusher, Model Number CAL11-44, Serial Number D2-76. Horizontal shaft, 12" X 44" center feed openings, swing type hammers, generates minimal fines @ 95% minus 1/4". Last used to grind coal to feed rotary kiln in cement plant. Less motor.
  13. Crusher, Impact, Horizontal, Penn, Mdl CAL11-44

    Crusher, Impact, Vertical, Cemco, Mdl MDEV80, 400 HP,

    Stock Number: S738844

    Cemco Turbo vertical shaft impact crusher, VSI, model MDEV80, Turbo80. Crushing chamber measures 6' diameter X 4' high sidewall, with 35" diameter Superchipper rotor assembly. Product is fed through 15" diameter center top opening thru rotor with 12" x 8" openings, spreading feed material into crushing chamber. Inside wall includes heavy duty anvil ring with stationary anvils along circumference of chamber. Rotor is driven by twin drives, 250 HP and 150 HP (460 volt, 1785 RPM, 3/60Hz) thru V-belt assemblies, connected to common sheave. Product discharges through 36" x 15" split discharges. Top cover is removeable with swing assembly, controlled by manually operated hydraulic cylinder. Serial# 4156.
  14. Crusher, Impact, Vertical, Cemco, Mdl MDEV80, 400 HP,

    Crusher, Jaw, 10" X 20", Mfg. Red Rhino

    Stock Number: A738989

    Jaw Crusher, 10" X 20" feed opening, manufactured by Red Rhino Crushers Ltd., UK, Model 3000. Portable unit, rated @ 15 tons/hour. Can be run with diesel engine, power take-off, or electric motor. Used for 20 hours only. Like new condition.
  15. Crusher, Jaw, 10" X 20", Mfg. Red Rhino

    Crusher, Jaw, 12" X 24", C/st, Pennsylvania,

    Stock Number: S741070

    Jaw crusher, 12" X 24" opening with adjustable jaws. Manufactured by Pennsylvania Crusher Corp., Type DT 12 X 24. Driven by 30 HP, 230/460V, 1755 RPM, 3/60Hz motor (25 HP @ 50 Hz). Previously used in glass crushing operation. Excellent condition.
  16. Crusher, Jaw, 12" X 24", C/st, Pennsylvania,

    Crusher, Jaw, 2-1/2" X 3-1/2", Denver, Lab Size

    Stock Number: D735904

    Jaw crusher, 2-1/2" x 3-1/2", manufactured by Denver, lab size unit.
  17. Crusher, Jaw, 2-1/2" X 3-1/2", Denver, Lab Size

    Crusher, Jaw, 36" X 42", Traylor, 125 HP, Mdl HB

    Stock Number: A737236

    Jaw crusher, 36" x 42" jaws, manufactured by Traylor, type HB, double toggle, driven by 125 HP motor, 5" closed side, crusher stroke, swing jaw 1". Includes automatic lube system.
  18. Crusher, Jaw, 36" X 42", Traylor, 125 HP, Mdl HB

    Crusher, Jaw, 36" X 48", Kemco, 150 HP,

    Stock Number: D737894

    Jaw crusher, 36" x 48" jaws, manufactured by Kemco, 36-42, Model C-120 ns driven by Westinghouse 150 HP motor. Seen very little use. Unit is same as Kue Ken Model 120 S, with parts being interchangeable.
  19. Crusher, Jaw, 36" X 48", Kemco, 150 HP,

    Crusher, Jaw, 4" X 6", C/St, Sturtevant, 2 HP,

    Stock Number: S741072

    Mild steel jaw crusher, manufactured by Sturtevant, model number 2 X 6. Jaw opening measures 4" X 6". Unit driven by 2 HP, 208-230V/460V, 3/60Hz, 1170 rpm motor enclosed in steel housing with access door. Previously used glass crushing operation. Unit new in 2008. Serial number 0600435. Good condition.
  20. Crusher, Jaw, 4" X 6", C/St, Sturtevant, 2 HP,

    Crusher, Jaw, 42" X 54", Kobe Steel,

    Stock Number: D735902

    Jaw crusher, 42" x 54", manufactured by Kobe Steel/Allis Chalmers, s-t. Complete with peripherals and accessories such as liners, drive motor, pulley and sheaves. Includes stationary jaw plate - corrugated 52" wide, cheek plates and side liners, fabricated swing jaw, swing jaw plates 51" wide, flywheel.
  21. Crusher, Jaw, 42" X 54", Kobe Steel,

    Crusher, Jaw, 5" X 8", Morse Brothers, 5 HP

    Stock Number: C740414

    Jaw crusher, 5" x 8", manufactured by Morse Brothers Machinery. Complete with 5 HP, 1200 RPM, 220/440 V. Toshiba motor. On stand with safety cage and gear gaurds. Condition excellent,last used on soft limestone. Serial number: JC136.
  22. Crusher, Jaw, 5" X 8", Morse Brothers, 5 HP

    Crusher, Jaw, 60" X 84", Allis Chalmers, 300 HP, Heavy Duty,

    Stock Number: D733965

    Jaw crusher, 60" x 84", Allis Chalmers, superior, heavy duty, complete lube system, 300 HP motor , 294 RPM, 2200 volt, 95 amps, 3 phase, 60 cycle. Rotor 350 volt, 400 amps. radiator oil coolers, double toggle. Jaws dies like new. Spare parts include: (2) spare bearing capsfor swing jaw, (2) used toggle plates, new toggle seat, (2) bearing races with babbit & (1) spare bearing cap.
  23. Crusher, Jaw, 60" X 84", Allis Chalmers, 300 HP, Heavy Duty,

    CRUSHER, JAW, 74" X 54", A/C, KOBE, SINGLE TOGGLE,

    Stock Number: D738069

    Jaw crusher, manufactureed by Kobe/Allis Chalmers, Model number 54-74, 74" x 54" jaws, single toggle. Offered less motor.
  24. CRUSHER, JAW, 74" X 54", A/C, KOBE, SINGLE TOGGLE,

    Crusher, Roll, 78" X 60", 2-Roll, FAM, (2) 350 HP, Primary

    Stock Number: S738503

    Double roll crusher, 78" diameter x 60" wide (2000 mm x 1500 mm) rolls, heavy duty teeth, manufactured by FAM, type ZWB 2015 HSm, up to 24" feed size, (1) roll is hydraulically adjustable for roll gap spacing, rolls driven by twin 350 HP, 4000 volt, 1187 RPM, 60 Hz motors thru gear reducers. Complete with lube system, discharge chute, hydraulic pump station, controls, etc. Previously used as primary crusher at phosphate minerals processing facility. Apron feeder also available. Equipment was dismantled and is now being stored at crane yard for easy loading.

24 Item(s)

per page

Set Descending Direction

Please wait...