BELT PRESS, 60" WIDE X 15' LONG, MANUFACTURED BY AMOS, MODEL AP 1500, STANLESS STEEL FRAME WITH S/ST AND PLASTIC ROLLERS & TOP MOUNTED SPRAY BAR. RATED FOR APPROXIMATELY 14 TONS/HR ON APPLES. INCLUDES PNEUMATICALLY OPERATED SCRAPER KNIFE MECHANISM. ROLLER... Learn More

BELT PRESS, 2 METER BELT WIDTH, STAINLESS STEEL CONSTRUCTION, FABRIC FILTER MEDIA, MANUFACTURED BY ANDRITZ, MODEL NO. SMXS8-LP, RATED FOR 1,500 LBS/HR SOLIDS CAPACITY. BELT IS DRIVEN BY 7-1/2 HP MOTOR WITH VARIABLE FREQUENCY DRIVE. APPEARS TO BE IN VERY G... Learn More

ANDRITZ BELT PRESS, 3.5 METER BELT WIDTH, MODEL NO. CPR-3500-S7. EPOXY COVERED MILD STEEL FRAME, RUBBER COVERED ROLLERS, EXTRA HEAVY DUTY DESIGN, LAST USED FOR COAL WASH PLANT, TAILINGS AND SLUDGE DEWATERING. UNIT IS LESS DRIVE MOTORS, CONDITION VERY GOOD... Learn More

BELT PRESS, 16" WIDE X 10' LONG, EIMCO "EXPRESSOR" PRESS, STAINLESS STEEL FRAME, HYDRAULICALLY DRIVEN, SERIAL # 82250-01B. INCLUDES SCRAPER BLADE CONNECTION ON END, STAINLESS STEEL COLLECTION PANS UNDER ROLLERS. MOUNTED ON I- BEAM FRAMES WITH CASTERS, HEA... Learn More

ENSINK BELT PRESS, WITH 54" WIDE STAINLESS STEEL ROLLERS, AND A 47" WIDE SANITARY POLYPROPYLENE MESH BELT. THE BELT IS 21-1/2' LONG WITH A 125" MAIN PRESSING SECTION, COMPLETE WITH S/ST KNIFE DISCHARGE, MIDDLE DRIP PAN SECTION WITH SIDE DISCHARGES, BOTTOM... Learn More

KOMLINE SANDERSON UNIMAT BELT FILTER PRESS, MODEL GMD-2/0. THIS UNIT IS A COMPLETE, 2 METER WIDE, STAINLESS STEEL PRODUCT CONTACT PART BELT PRESS. UNIT FEATURES PNEUMATICALLY CONTROLLED BELT TRACKING DEVICE. PRESS FEATURES 1 HP, DC FEEDER BELT DRIVE AND 2... Learn More

PCP (PROIPAFISA) BELT PRESS, MODEL 2500/91, 2.5 METER BELT WIDTH. ALL WETTED PARTS ARE SANITARY STAINLESS STEEL. THE PRESS IS EQUIPPED WITH WAUKESHA INFEED PUMP WITH A 15 HP VARI-SPEED DRIVE, HYDRAULIC BELT TENTIONING AND ROLL ADJUSTMENT WITH HYDRAULIC DR... Learn More

(2) PNEUMAPRESS BELT FILTER PRESS, 1 METER DIAMETER PLATE, CONSISTS OF TITANIUM UPPER AND LOWER PLATE WHICH HYDRAULICALLY PRESSES ONTO A TRAVELING BELT. UPPER PLATE FORMS A CHAMBER WHERE SLURRY AND COMPRESSED AIR ARE INTRODUCED, LOWER PLATE COLLECTS LIQUI... Learn More

WILLMES MODEL TP-8 BLADDER PRESS, 8,000 LITER CAPACITY. STAINLESS STEEL. CAPACITY IN TONS 8.8T. VARIABLE FULLY AUTOMATIC CONTROL ADJUSTABLE TO ANY VARIETY OF GRAPES. 4 HP DRIVE. LAST USED FOR PRESSING GRAPES. GOOD CONDITION. ... Learn More

BRIQUETTING PRESS, 47" (1.2M) DIAMETER ROLLS, MANUFACTURED BY SKB (SIMILAR DESIGN TO KOMAREK GREAVES), PRESSES 925 BRIQUETTES/REV, APPROXIMATE CAPACITY BETWEEN 25 30 TONS/HR, INCLUDES TWIN HYDRAULIC RAMS RATED FOR 2500 PSI EACH SIDE GIVE SEPARATING FORCE... Learn More

PRESS, PLATEN, 10" x 10" WITH 8" RAM, 9" DAYLIGHT. OVERALL DIMENSIONS ARE 2' H x 15" x 6' FRAME. UNIT DRIVEN BY 3 HP DRIVE. PRESS ONLY.... Learn More

PRESS, NORCAP, HYDRAULIC PLATEN, 10" x 11" WITH 8" RAM, 9" DAYLIGHT. OVERALL DIMENSIONS ARE 7' H x 33" x 44" FRAME. UNIT DRIVEN BY 3 HP HYDRAULIC DRIVE.... Learn More

(2) PRESS, PLATEN, ATLAS PACIFIC JUICE PRESS, 48" x 48" PLATEN HYDRAULICALLY ACTUATED WITH PNEUMATIC BLADDER. AUTOMATIC ADVANCING POLYPROPYLENE BELT FOR PULP DISCHARGE. PRESS IS ALL SANITARY STAINLESS STEEL CONTACT PARTS, INCLUDES 10' x 43" AGITATED LOADI... Learn More

PRESS, PLATEN, JUICE, STAINLESS STEEL, HYDRAULIC, 28" x 28". ... Learn More

PRESS, PLATEN, JUICE, STOLL III, S/ST, AUTO, 24" X 24", SANITARY STAINLESS STEEL WETTED PARTS, WITH A 20 HP HYDRAULIC POWER PLANT, ELECTRICAL CONTROLS, STAINLESS STEEL FEED HOPPER, STAINLESS STEEL SCREW FEED ELEVATOR, UNITIZED.... Learn More

PRESS, GRAPE ROLLER CRUSHER, DEMOISY MODEL F-1-2. SERIAL NO. F-1207. 1989. ... Learn More

PRESS, RIETZ, MODEL RVP-60K, STAINLESS STEEL PRODUCT CONTACT PARTS. WITH 60 HP MAIN MOTOR DRIVE THRU GEARBOX. S/N RVP-710304.... Learn More

COQ HYDRAULIC CONTINUOUS SCREW PRESS, MDL 800 WITH AN 800mm STAINLESS STEEL SCREW, S/ST MAIN SCREEN AND C/ST BACK UYP RIBBING. PRESS INCLUDES S/ST COVERS, 30 HP HYDRAULIC MAIN DRIVE WITH PUMP AND RESERVOIR, HYDRAULIC DISCHARGE GATE.. VERY GOOD CONDITION.... Learn More

BELOIT JONES MODEL P-40 PRESSMASTER, SCREW PRESS, VERTICAL, STAINLESS STEEL CONTACTS. REPORTED TO BE IN GOOD CONDITION.... Learn More

JONES HORIZONTAL SCREW PRESS, MODEL 4225, ALL WETTED PARTS BEING 304 STAINLESS STEEL. THE UNITS ARE EQUIPPED WITH 50 HP MAIN DRIVES, HYDRAULIC CONE MECHANISM, STAINLESS STEEL MAIN AND BACK-UP SCREENS, COVERS, DISCHARGE, DRAINAGE PAN, UNITIZED. IS IN EXCEL... Learn More

JONES SCREW PRESS, MODEL P-125, CARBON STEEL. UNIT HAS TOP INLET, CONE BOTTOM, LESS BASE, NOT COMPLETE. PARTS MACHINE ONLY. ... Learn More

(2) JONES VERTICAL SCREW PRESS, MDL P-225, TYPE 2512, WITH ALL WETTED PARTS BEING STAINLESS STEEL. UNIT EQUIPPED WITH 20 HP MIAN DRIVE THRU GEARBOX, FRAC HP, DRIVE ON THE SHAKER DISCHARGE ASSEMBLY AND AIR CYLINDER TO OPERATE THE SOLIDS DISCHARGE CONE. INC... Learn More

PERA HORIZONTAL SCREW PRESS, MDL 800 WITH 800 mm STAINLESS STEEL CLAD SCREWS. UNIT IS HYDRAULICALLY DRIVEN WITH 25 HP DRIVE SYSTEM, HAS REGULATED DISCHARGE DOORS AND UNITIZED ON LEGS. INCLUDES STAINLESS STEEL INFEED CHUTE, S/ST COVERS, LAST RUNNING GRAPES... Learn More

SCREW PRESS, RIETZ, 12" HORIZONTAL, MODEL RSP-12-K2, WITH 304 STAINLESS STEEL CONTACT PARTS, 10 HP VARI SPEED MOTOR AND 1 HP VARI SPEED CONE DRIVE. CONE IS PNEUMATICALLY ACTUATED FOR BACK PRESSURE ON PRESS. PRESS IS COMPLETE, MOUNTED ON STAND, AND OFFERED... Learn More

RIETZ SCREW PRESS, MODEL# RSP-16-K2, 16" DIAMETER SCREW, ALL STAINLESS STEEL CONSTRUCTION, INCLUDING FRAME AND LEGS. SCREW IS DRIVEN BY 20 HP MOTOR THROUGH V-BELT DRIVE AND HEAVY DUTY GEARBOX. CONE IS DRIVEN BY 5 HP, 208-230/460V MOTOR THRU GEARBOX. SERIA... Learn More

MANESTY BETA PRESS ROTARY TABLET PRESS, 16 STATION, KEYED UPPER PUNCH GUIDE, SINGLE SIDED, FORCE FEEDER WITH HOPPER, RECOMPRESSION, 6.5 TON TOTAL COMPRESSION PRESSURE, 5/8" MAXIMUM TABLET DIAMETER, 11/16" MAXIMUM DEPTH OF FILL, RATED UP TO 1500 TABLETS PE... Learn More

MANESTY BETA PRESS ROTARY TABLET PRESS, 16 STATION, KEYED UPPER PUNCH GUIDE, SINGLE SIDED, FORCE FEEDER WITH HOPPER, RECOMPRESSION, 6.5 TON TOTAL COMPRESSION PRESSURE, 5/8" MAXIMUM TABLET DIAMETER, 11/16" MAXIMUM DEPTH OF FILL, RATED UP TO 1500 TABLETS PE... Learn More

MANESTY BETA PRESS ROTARY TABLET PRESS,23 STATION, PRE-COMPRESSION 6.5 TON TOTAL COMPRESSION PRESSURE, 7/16" MAX TABLET DIA., 11/16" MAX DEPTH OF FILL, RATED UP TO 2160 TABLETS/MIN. KEYED UPPER PUNCH GUIDES, PROVISION FOR FORCE FEED WITH HOPPER. ... Learn More