+1-415-467-3400

Search results for 'ball mill'

Items 1 to 50 of 183 total

per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4

Set Ascending Direction
  1. D739009_A

    Mill, Ball, 4' X 8', Denver, 50 HP, Wet Grind,

    Stock Number: D739009

    Denver 4' diameter X 8' long ball mill, driven by 50 HP, 208-220/440 V, 1785 RPM, 3/60 Hz motor with soft start. Previously used at wet grind ball mill. Includes steel liners (new rubber liners available separately).
  2. D739663

    Mill, Rod, 13' X 18'8", Nordberg, 1,500 HP, (2)

    Stock Number: D739663

    (2) Nordberg 13' diameter x 18' 8" long rod mill with 1,500 HP Westinghouse synchronous motor through Fawick model 42VC1200, no liners, single compartment, wet, overflow discharge. Mill is complete with automatic gear lubrication system. Last used as a rod mill; however, this mill is identical to a ball mill design. Mill was manufactured in 1970. Previously used to grind coal to 100 mesh only for pumping in a slurry pipeline to a power plant, excellent condition.
  3. S738509_A

    Mill, Ball, 13' X 21', Allis Chalmers, 2000 HP, R/L,

    Stock Number: S738509

    Ball mill, 13' diameter x 21' long, Manufactured by Allis Chalmers (Svedala), rubber-lined mill, with Siemens-Allis 2,000 HP, 4000 volt, 200 RPM synchronous motor, Eaton airflex clutch. Includes trommel discharge, ball mill rejects conveyor, lube system, etc. Offered complete with controls. New in 1979. Completely rebuilt in 1998, Serial number C-2485. Previously used at phosphate minerals processing facility. Also available pumps, spare parts, drives, controls to comprise of complete mill system.
  4. D739010

    Mill, Ball, 2' X 4', Marcy, 5 HP

    Stock Number: D739010

    Marcy 2' diameter X 4' long ball mill, driven by 7.5 HP gear motor thru chain and sprocket. Offered with ball charge, steel liners and self lubricator.
  5. D733559_A

    Mill, Ball, 9' X 15', Kobe-Allis Chalmers, 600 HP,

    Stock Number: D733559

    Ball mill, 9'diameter (2745mm) x 15' long (4570mm), Manufactured by Kobe-Allis. Last used as regrind ball mills in copper circuit, each complete with Yasakawa 450 kw (603 HP) synchronous motors, 3300 volts, 60 cycles. Rate at 35 metric tons per hour capacity.
  6. D739646

    Mill, Ball, 22' X 36'5", Metso, 6,250 HP, Unused, (2)

    Stock Number: D739646

    (2) Unused Metso ball mill, 22' (6.71 m) diameter x 36' 5" (11.13 m) long, 2- GE Dual Pinion Synchronous 6,250 HP (4,650 kw) 50 Hz motors-operating frequency 50 Hz. Mill speed: 12.44 RPM. Maximum volumetric load: 45%. No liners.
  7. S484980

    Mill, Ball, 8' X 6', Marcy, 250 HP,

    Stock Number: S484980

    Marcy 8' diameter x 6' long ball mill with trunnion feed and discharge. Rubber liners and lifters. Last used in a wet grind application. Previously driven by 250 HP motor thru gear & pinion. Gears good. Lots of wear on (1) of the trunnions. Mill serial number 700. Previously used in silica sands operation
  8. D739654

    Mill, Ball, 6' X 6', Metso, 163 HP, (2)

    Stock Number: D739654

    (2) Metso (Allis/Svedala) ball mill, 6' (1.8 m) diameter x 8' (2.5 m) long, 163 HP (1200 kw).
  9. D739645

    Mill, Ball, 26' X 40'6", FL Smidth, No Motor, Unused, (2)

    Stock Number: D739645

    (2) Unused FL Smidth ball mill, 26' (7,925 mm) diameter x 40' 6" (12,344 mm) long, designed for 22,000 HP (16,400 kw) wrap around GMD motor [not included]. No liners.
  10. D739656

    Mill, Ball, Metso, Mdl VTM-1500-WB, 1,500 HP, Unused,

    Stock Number: D739656

    Unused Metso ball mill, Model VTM-1500-WB Vertimill Grinding Mill, Screw Speed: 18.9 RPM, Direction of Screw Rotation: Clockwise (Viewed from Top), Speed Reducer Size and Type: Moventas Planetary Gear Reducer, D3PHX180VM, with External Lubrication System, Speed Reducer Nominal Ratio: 51:1, Mill Drive Motor Size & Speed: Weg, 1,500 hp (1,120 kW), 6000V, 50 Hz, 1000 RPM, Drive Motor Power Draw: 100%, Grinding Media: Steel Grinding Balls.
  11. C739517

    Mill, Ball, Batch, 30" X 24", Ceramic, 2 HP

    Stock Number: C739517

    Ball mill, batch type, 30" diameter X 24" long grinding chamber which is ceramic lined. Complete with 2 HP motor thru gear reducer, on stand, condition of liners good. There may not be a running door.
  12. A736765

    Mill, Vibratory, Palla, 50, 100 HP, Jkt, Micronizer

    Stock Number: A736765

    Palla vibrating ball mill, Micronizer, Model# 50, complete with 100 HP main drive and control box, unit is water jacketed. Can be used on explosive materials. Capable of milling down to sub-20 micron level. Very good condition.
  13. D739662

    Mill, Ball, 9' X 11', Allis Chalmers, 250 HP,

    Stock Number: D739662

    ALLIS CHALMERS 9' (2.74m) diameter X 11' ( 3.35m) long, dribble regrind ball mill, manufactured in 1971, refurbished by Metso, 250 HP (184 kW), 1,200 RPM motor, lube system and complete set of unused metal liners. Unit has a grate discharge, excellent condition.
  14. D733555

    Mill, Ball, 10' X 18', Allis Chalmers, 800 HP,

    Stock Number: D733555

    Allis Chalmers ball mill, 10' diameter(3082 mm) x 18' long(5486 mm), wet overflow type, Serial number C2482. Complete with bull gear and pinion drive through speed reducer. Motor no longer available last used 800 HP. No liners. Good condition.
  15. A738791_A

    Mill, Ball, 9' X 18', Traylor, 600 HP, (2)

    Stock Number: A738791

    (2) Fuller-Traylor ball mill, 9' X 18' with 600 HP, 4160 volt, 1800 RPM motor. Complete with lube system, gearbox, air clutch and classifiers. Trunnion feed, overflow discharge. Still installed. Last used for limestone for power plant scrubber. Spare parts available. New 1992.
  16. D739655

    Mill, Ball, 14'9" X 24'5", Nordberg, 3,485 HP,

    Stock Number: D739655

    Nordberg ball mill, 14' 9" diameter(4.5 m) x 24' 5" long(7.45 m), type CRRK with roller bearings. Size 4.5 m diameter inside shell diameter x 7.450 m flange to flange (7.0m EGL). Fitted with combination of with composite steel-rubber end and shell linings with rubber grate. Equipped with 2600 kW single pinion drive, consisting of 2600 kW wound rotor induction motor driving through speed reducer and flexible couplings to a single pinion, with inching drive. Lube/cooling sets for gearbox, separate grease lube sets for ring gear and roller bearings and seals. All mill instrumentation and electrics included with mill. Feed chute and trommel included. Liners are reusable and included.
  17. S738065

    Mill, Ball, Batch, 4' X 2'6", Stevenson, 7.5 HP, Porcelain,

    Stock Number: S738065

    Stevenson batch ball mill, 2'6 diameter X 4' long. Unit is porcelain lined, with carbon steel outer skin. Unit has 7.5 HP, 230/460V, 1760 RPM drive inline to gearbox with ratio of 63. Unit is complete with a-frame stand, less charge. Very good condition.
  18. D739661

    Mill, Ball, 9.6' X 19.4', Metso, 1,005 HP,

    Stock Number: D739661

    Metso EGL wet overlfow regrind ball mill, 9.6' (3.0 m) diameter x 19.4' (5.95 m) long, pinion speed: 169.3 RPM, mill speed: 18.74 RPM, girth gear: 244 teeth (7.5" right hand, hHelix 25 deg. P.A., 2318 Centres, 1.5 D.P.), pinion: 27 teeth, drive motor: Teco 1005 HP (750 kW), 4,160 volts, 1,182 RPM, 4-pole, 60 Hz, wound rotor 6P, LRS: NHP M350 Vapormatic, reducer: H2SH14 (Ratio: 6.98:1), incher: K148-G13254/L80N, main bearing size: 239/750 Antifriction, low speed coupling: Zapex Zin 6, high speed coupling: N-Eupex A440, main bearings lubrication: Tecalemit grease (dual line), feed spout I.D.: 250, trammel: 0.55m I.D. x 1.5m long.
  19. S739710_A

    Mill, Ball, 2'6" X 1'10", 3 HP, Porcelain, 65 Gal, 9 CF,

    Stock Number: S739710

    Process Equipment porcelain ball mill, approximately (2'6" X 1'10") diameter x 22" long with internal brick. Unit is approx. 9 cu/ft (65 gallon) capacity, driven by 3 hp, 220/440 volt, 1740 rpm motor 11.4:1 ratio, thru gearbox. Unit has charge/discharge with cover, has babbitt bearings, is mounted on carbon steel stand.
  20. S738884_A

    Mill, Ball, Batch, 3' x 32", Paul O Abbe, Less Drive, C/st

    Stock Number: S738884

    Paul O'Abbe ball mill, 32" diameter x 3' long mounted on stand. Unit is carbon steel contacts, jacketed for water cooling, less drive with 24" gear x 3" and 26" diameter x 5" sheave. Unit has 9-1/2" x 8" door. Unit has 9-1/2" x 8" door.
  21. D739642

    Mill, Ball, 10.5' X 15', Allis Chalmers, 800 HP, (2)

    Stock Number: D739642

    (2) Allis-Chalmers/Kobe Steel ball mill, 10.5' diameter (3.23 m) x 15' long (4.57 m), complete with bull gear, ring gear (364 teeth X 2" X 24" face), and pinion drive (29 teeth X 2" X 24" face). New babbit inserts, 800 HP induction motor (885 rpm, 3 ph, 60 Hz), and gear box (4:03:1).
  22. S738883_A

    Mill, Ball, Batch, 4' x 4', Western, 5 HP, S/st

    Stock Number: S738883

    Western Machinery ball mill, 4' diameter x 4' long, mounted on carbon steel frame. Unit water jacketed for cooling, with 5 HP, 230/460 volt, 3 phase drive to gear reducer. Unit is stainless steel contact parts, complete with discharge door with valve measuring 13-3/4" x 10". Serial number 81-1770.
  23. D733556_A

    Mill, Ball, 10' X 10', Kurimoto Iron Works, 370 KW,

    Stock Number: D733556

    Ball mill, 10' diameter (3.05m) x 10' long (3.05m), wet overflow discharge, Serial number M4-371, Manufactured by Kurimoto Iron Works Ltd, 1969. Rated at 1020 ton per day capacity, complete with 370 kw induction motor, 3 phase, 60 cycle, 460 volts, 1190 RPM through SKK Kogyosho Ltd. Gear reducer, 177.5 RPM output. Complete with lubrication system & electrical controls, no balls or liners.
  24. S739708_A

    Mill, Ball, 2'3" X 3'2", 3 HP, Porcelain, 90 Gal, 13 CF

    Stock Number: S739708

    Porcelain ball mill, approximately (2'3" X 3'2") 27" diameter x 38" long with internal brick. Unit is approximately 13 cubit feet (90-gallon) capacity, driven by 3 hp, 220/440 volt, 1880 rpm motor, shaft rpm of 100 thru gearbox. Unit has charge/discharge with cover, mounted bearings, is mounted on carbon steel stand. No nameplate data available.
  25. D739660

    Mill, Ball, 13.5' X 28', Metso, 8,800 HP, (2)

    Stock Number: D739660

    (2) Metso 13.5' (4.1 m) diameter x 28' (8.53 m) long ball mill, with ABB 2800 HP (2,088 kW), 900 RPM Motors, 3 Ph, 60 Hz, 4000 volts. Unit includes: clutch: Eaton Airflex 42VC1200 (Dual Wide), speed reducer: Falk 3515Z1S (Ratio: 4.571:1), inching drive: Falk with brake, connected to the extended drive motor shaft, bull gear: 254 teeth, pinion gear: 21 teeth (Ratio: 12.09:1), mill speed: 15.92 RPM, % of critical speed: 76%, trunnion bearing size: 66" x 22" (type: Hydrodynamic Sleeve Bearings), trunnion bearing lube system: 700AL-duplex lubrication system, liners are no longer available; previous mill lining: Chrome (Moly metal liners-double wave design), feed arrangement: feed bowl, lined spout feeder, feed trunnion liner with seal assembly, discharge arrangement: discharge trunnion liner, trommel, and discharge housing.
  26. S739709_A

    Mill, Ball, 2'8" x 4', 10 HP, Porcelain, 175 Gal, 24 CF

    Stock Number: S739709

    Patterson Industries porcelain ball mill, approximately (2'8" X 4') or 32" diameter x 48" long with internal brick. Unit is approximately 24 cubic feet (175-gallon) capacity, driven by 10 hp, 220/440 volt, 1880 rpm motor, shaft rpm of 155 thru gearbox. Unit has charge/discharge with cover, has babbitt bearings, is mounted on carbon steel stand. Serial number K2077.
  27. S737518_A

    Mill, Ball, Batch, 3' X 4', Abbe, 10 HP, C/St, Jkt,

    Stock Number: S737518

    Paul O Abbe steel ball mill, 3' diameter x 4' long mounted on stand. Unit is water jacketed for cooling, complete with 10 HP, 230/460 volt motor drive with v-belt to torque arm reducer. Unit mounted on stand, complete with running door. Unit last used for wet grinding paint products.
  28. C739037_A

    Mill, Ball, 3' X 24", Hardinge, Conical Mill,

    Stock Number: C739037

    Hardinge 3' x 24" diameter ball mill, conical shape, includes feed hopper, screw feeder, screw takeaway and discharge elevator. Offered complete with hardened steel factory liners. Liners are in good condition. New motor added 1 year ago and was in good running condition when removed from service.
  29. D739658

    Mill, Ball, 11'6" X 18', Hardinge, 1,250 HP, (2)

    Stock Number: D739658

    (2) Hardinge ball mill, 11'6" (3.5 m) diameter X 18' (5.5 m) long, cylindrical, 1,250 HP (932 kW) motor, manufactured in 1975, shell speed: 16.9 RPM, rubber liners, gear and pinion ratio: 318/22, countershaft speed: 244.31 RPM, speed reducer size and type: Horsburgh & Scott, 1050P Single Reduction - Parallel, shaft centurion speed reducer and Eaton clutch: ratio 4.789:1, motor HP: 1250 General Electric, 1,185 RPM, 4,000 Volts, 3 phase, 60 Hz.
  30. D739657

    Mill, Ball, 14' X 23', Kobe Steel, Allis Chalmers, No Motor

    Stock Number: D739657

    Kobe Steel/Allis Chalmers, 14' (4.2 m) diameter x 23'(7 m) long ball mill. Unit has feed & discharge trunnion Bbaring housing and inserts. Unit is missing pinion gear, pinion shaft, bull gear, lube system and motor. Grinding capacity at previous installation was 120 MT per hour, single compartment (diaphragm type), grinding media capacity was 150 MT, lubrication of main trunnion bearing (babbit type).
  31. Mill, Ball, 27' X 46', FL Smidth, Unused,

    Mill, Ball, 27' X 46', FL Smidth, Unused,

    Stock Number: D739659

    Unused FL Smidth wet grind overflow ball mill, 27' (8.23 m) diameter x 46' (14.02 m) long. Discharge with 20.5 MW (20,500 kW) gearless wrap around motor drive, 50 Hz, shell inside diameter: 8,230 mm, shell length: 14,021 mm, shell EGL: 13,956 mm, shell plate thickness: 105 mm, trunnion inside diameter: 3,410 mm, trunnion type: demountable for bolting to heads, bearing type: hydrostatic multi-pad (4 pads per bearing), bearing size: 4,060 mm diameter x 900 mm wide, bearing material: bronze, bearing lubrication type: hydrostatic, feed chute: sump tank, removable spout, mounted on truck assembly.
  32. C736519

    Mill, Sand, Petzholdt, 10" X 4-1/2', C/st,

    Stock Number: C736519

    Media mill, manufactured by Petzholdt, measures 10" diameter x 4-1/2' high, carbon steel construction, jacketed with 1" jkt connections, includes media/ball charge, used in chocolate processing facility. Recently replaced bearings. Comparable to Model HKM80. Good condition.
  33. D739650

    Mill, Ball, Batch, 3'9" X 4', Paul O Abbe, No Motor,

    Stock Number: D739650

    Paul O. Abbe Model 4A pebble/paint mill, 3' 9" (1.14 m) x 4' (1.22 m), ceramic lined, batch type mill. Total mill volume: 251 gallons. Mill speed: 27 RPM when 50% full of pebbles or porcelain balls, missing hatch, Pinion gear: 4" wide, 1' center to center tooth, 120 teeth;drive gear has 28 teeth. Previously driven by a 10 HP electric motor.
  34. S485829

    Mill, Batch, 2'6" X 3'6", Patterson, 5 HP, C/st, Jkt,

    Stock Number: S485829

    Patterson Steel paint mill, 32" diameter X 42" long, with approx 65 gallon working capacity, batch type mill. Mill is jacketed for 14 PSI as cooling jacket. Unit rated 128 gallons total capacity. Unit is complete, mounted on stand. Overall dimensions are 3' wide x 4' long x 42" high. Mill is in good condition with main bull gear in need replacement. Serial number R-387.
  35. S516500

    Mill, Impact, Tas, C/st, 350 HP, Mdl 42B, (2)

    Stock Number: S516500

    (2) Vertical shaft impact mill, Theory Application Service (TAS) Model 42B with 350 HP vertical v-belted electric motor drive. Mill has a 42" diameter 5-stage rotor and last used to mill coal to 200 mesh for kiln feed at the rate of 6 TPH in a cement plant. Drawings available.
  36. S485828_A

    Mill, Ball, Batch, 2'8" X 3', Abbe, 7.5 HP, C/St, Jkt,

    Stock Number: S485828

    Paul O Abbe steel paint mill, 32" x 3', with 50 gallon working capacity, batch type mill. Jacket test pressure is 40 PSIG; working 14 PSIG. Mill driven by 7.5 HP, 230/460 volt, 1746 RPM motor to torque arm reducer, unitized on stand. Serial number A-21668.
  37. Mill, Vibratory, Sweco, M-45, C/st, 2.5 HP,

    Mill, Vibratory, Sweco, M-45, C/st, 2.5 HP,

    Stock Number: S523530

    Mill, Sweco Vibro-Energy wet grinding, model M-45. Low amp mill. Unit has maximum working capacity of 27 gallons, includes welded-in stainless steel liner. Complete with 2.5 HP, 1200 RPM, 440V, 3-phase, 60Hz drive motor, carbon steel cover. Mill is in very good condition, offered less media charge. Serial number is 45M-263-3.
  38. S738506

    Mill, Sag, 18' X 10-1/2', Fuller, 1500 HP, R/L,

    Stock Number: S738506

    SAG mill, 18' diameter x 10-1/2' long, manufactured by Fuller, rubber-lined, driven by 1500 HP, 4160 volt, 1192 RPM, continuous motor, 5010 frame, thru Moventas gear reducer, 4.5:1 gear ratio, 264.4 output RPM, mfg# C001338. Complete with Robicon Perfect Harmony VFD drive & 2-piece gear inching motor. Includes stationary & ball feed chutes, discharge chute, reject chute, retractable feed chute, etc. Offered with discharge belt conveyor, & SAG rejects conveyor, complete with lube system, manufactured by Howard Marten, Model number M8375F, order# M42483, includes oil pumps, cartridge filters, etc. Previously used at phosphate minerals processing plant. Also available McLellan liner handler, 4000 lb. capacity, with hydraulic pump, approx. 25 HP; pumps, spare parts, drives, controls to comprise of complete mill system. New in 1998.
  39. A513260

    Mill, Roller, Raymond, Mdl 5047, 75 HP,

    Stock Number: A513260

    Raymond roller mill, Model 5047 high side. Complete with 75 HP, 1200 RPM, 440V main motor thru V-belt drive. Exhaust blower has 75 HP 440V motor. Mill is equipped with 6' diameter double Whizzer separator with 10 HP motor thru V-belt to vari drive. Motorized feeder with 1 HP motor, complete mill system still installed with duct work, cyclone, dust collector, controls and considerable spare parts. Mill was completely rebuilt in 1977, new Whizzer installed 1990.
  40. S479979

    Mill, Hog, Mitts & Merrill, C/st, 75 HP, Mdl 13CD,

    Stock Number: S479979

    Mill, Mitts & Merrill, model 13CD, wood hog. Mill has 30" diameter x 13" wide solid rotor with adjustable knives. Requires up to 75 HP.
  41. D739643

    Mill, Sag, 38' X 25'5", Metso, 26,016 HP, Unused

    Stock Number: D739643

    Unused Metso sag mill, 38' (11.58 m) diameter x 25' 5" (7.76 m) long, 26,016 HP (19,400 kw) Siemens wrap around drive motor-operating frequency 50/60 Hz. EGL: 22' (6.7 m), mill speed: 7.5-10.08 RPM. Maximum volumetric load: 35%. No liners. Manufactured new in 2010.
  42. Mill, Pellet, California, 150, C/st, 150 HP

    Mill, Pellet, California, 150, C/st, 150 HP

    Stock Number: A736727

    Pellet mill, manufactured by California Pellet Mill (CPM), Model 150, driven by 150 HP, 440V main drive, reported to be in good condition.
  43. D733947

    Mill, Sag, Dry, 30' x 7', Allis Minerals (Svedala), 4000 HP,

    Stock Number: D733947

    Sag mill, manufactured by Allis Minerals (Svedala), 30' diameter x 7' long, dry grind, driven by 4000 HP motor, 200 RPM, 3300 v, 214 amps; mill was installed in 1993; still intact and gets turned every 2 weeks; overall condition is excellent.
  44. S478580

    Mill, Hammer, 30 HP, C/st, 24" X 10",

    Stock Number: S478580

    Hammer mill, carbon steel product contact parts, driven by 30 HP main motor drive. Unit features 12" x 14" feed hopper. Mill chamber measures 24" diameter x 10" wide. Unit features four sets of 2 fixed slugger hammers with 1" diameter carbon steel screen. Unit has 10" x 15" discharge. Mill is unitized on stand with V-belt drive.
  45. Mill, Dispersion, Kady, S/st, 30 HP, OC-30, Jkt,

    Mill, Dispersion, Kady, S/st, 30 HP, OC-30, Jkt,

    Stock Number: Z468800

    Kady mill, Model OC-30, serial number 1829, with 60 gallon stainless steel jacketed tank and 30 HP under driven agitator. Mill is mounted on structural steel stand.
  46. S664635

    Screen, Sifter, Gump, CP-43, S/st, Pressure, 48",

    Stock Number: S664635

    Gump Bar-Nun CP43 pneumatic in-line screens, 48" diameter pressure sifter, 15 PSI, test pressure 25 PSI (1) 6" inlet, (1) 5" outlet. (3) stainless steel sieves and (2) stainless steel trays. Screen area 33 sq. ft. With 2 HP, 340/460v, 3-phase, 60Hz enclosed, and static free motor, V-belt drive with belt guard. Dust tight, screening chamber is 304 stainless steel, capable of operating up to 15 PSI, feature flexible inlet and outlet connections for vacuum system, are complete with stainless steel ball carrier wire and rubber ball cleaners.
  47. S739686_A

    Mill, Sand, 15 Gallon, Premier, Mdl HM15, S/st, 20 HP

    Stock Number: S739686

    Premier model HM15 sand mill, stainless steel contacts with 20 hp main motor drive. Unit includes 1.5 hp feed pump, 460 volt. Mill built in 9/1982, serial number HM15-20-1-1/2TD- V-4-81-0017.
  48. S738164_A

    Mill, Pellet, California, 150, 150 HP, (2)

    Stock Number: S738164

    (2) California pellet mill, manufactured by CPM, driven by 150 HP motor, floating die pellet mill. Mill includes feed auger measuring 12" diameter x 5' long, leading to conditioner measuring 16" diameter x 5' long, feeding to milling section with perforated plate, measuring 26" diameter and includes (3) 10" diameter rollers and stationary wiper blades. Main motor is 150 HP, 1775 RPM, 230/460V, 3/60Hz motor. Serial numbers 150FD197270-1 & 150FD221634-2.
  49. S739035

    Mill, Sand, Eiger, Mdl .75LVSEEXP, 3.7 kw, Media

    Stock Number: S739035

    Eiger media mill, model .75L VSE EXP, with stainless steel jacketed chamber. Unit driven by 3.7 kw, 230 volt, 4000 rpm drive and includes a Viking mdl FH32 1/2 hp pump, 208/230/460 volt, 1725 rpm, s/n 311201. Mill was mfg new 1990 and is serial number 1492.
  50. Mill, Sag, 30' X 7', Allis Minerals (Svedala), 4000 HP,

    Mill, Sag, 30' X 7', Allis Minerals (Svedala), 4000 HP,

    Stock Number: D733957

    Allis Minerals(Svedala), sag mill, 30' diameter x 7' long, 4000 HP motor, 200 RPM, 3300V, 214 amps. Liners still installed, reverse side of pinion unused and mill can run in reverse direction, Airflex 52CV clutch, complete with all electrics, controls and lube system. New 1993.

Items 1 to 50 of 183 total

per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4

Set Ascending Direction

Please wait...