INDUSTRIAL COMBUSTION 150 HP FIRE TUBE BOILER. UNIT RATED AT 150 PSI STEAM, NATIONAL BOARD CODE STAMPED, INCL INPUT NATURAL GAS BURNER RATED AT 63,000 CU/FT P/HR, 6.3 MILLION BTU INPUT. BOILER WAS MFG NEW 7/83 AND RE-TUBED IN 1991, APPEARS TO BE IN VERY G... Learn More

PARKER BOILER, 90 HP STEAM BOILER, RATED FOR 150 PSI, MODEL 105-90, MAXIMUM INPUT RATING IS 3.78 MILLION BTU/HOUR, MINIMUM INPUT IS 1.89 MILLION BTU/HOUR, NATURAL GAS FIRED. RATED FOR 456 SQ.FT HEATING SURFACE. ALSO RATED FOR 3,105 LBS PER HOUR OF STEAM C... Learn More

ALLIS CHALMERS MODEL 1208 COMPACTING MILL, WITH 12" DIA. X 8" FACE CHROME PLATED SMOOTH COMPACTING ROLLS, 100,000 POUNDS OF SEPARATION FORCE, THE MILL IS EQUIPPED WITH A 25 HP VARIABLE SPEED MAIN MOTOR DRIVE, 3 PHASE 60 CYCLE 220/440 VOLT, (2) JONES GEAR ... Learn More

INGERSOL RAND AIR COMPRESSOR, 350 HP, RATED AT 1537 CFM @ 125 PSI. MODEL EP-350, TYPE SSR, LOBE TYPE COMPRESSOR UNITIZED ON SKID IN CABINET. FAN COOLED, COMPLETE WITH 350 HP, 3 PHASE, 60 CYCLE, 440V MOTOR. SINGLE STAGE TYPE, LAST USED AS SOURCE OF COMPRES... Learn More

CONE CRUSHER, LAB SIZE BRAUN SAMPLE CRUSHER,"COFFEE MILL", 6" DIAMETER, MOUNTED ON STAND, ADJUSTABLE CRUSH SIZE, LESS MOTOR. ... Learn More

BARR-ROSIN STAINLESS STEEL "RING-TYPE" FLASH DRYER, 4,410 LBS/HR FEED RATE @ 8% MOISTURE, 4065 LBS/HR FINISHED PRODUCT, INLET TEMPERATURE 650F, OUTLET TEMPERATURE 450F. DRYER INCLUDES S/ST 30" X 6' V-SHAPED HOPPER, 6" X 10' S/ST SCREW CONVEYOR, 20 HP HAMM... Learn More

BOWEN STAINLESS STEEL FLASH DRYER, 800 LBS PER HOUR FEED AT 67% WATER, SYSTEM COMPLETE WITH GAS BURNER WITH STAINLESS STEEL FIREBOX, STAINLESS STEEL PIN MILL WITH 20 HP DRIVE, STAINLESS STEEL "CLASSICLONE" CLASSIFIER/ CYCLONE SEPARATOR WITH CARBON STEEL P... Learn More

FILTER, ULTRA STATION, MILLIPORE, WITH 4 STAINLESS STEEL TUBULAR CANISTERS, 4" DIA x 48". UNIT IS MANIFOLDED TOGETHER, CARRIES MILLIPORE P/N MSD703W6, S/N M87080. UNIT INCLUDES STAINLESS STEEL SKID WITH STAINLESS STEEL ELECTRIC CABINETS AND CONTROLS. UNIT... Learn More

MILLIPORE 5 HP "PRO STAK" ULTRAFILTRATION SYSTEM, MODEL MSD940W9, S/N M900052.... Learn More

VERTICAL KILN / FURNACE, 30" ID x 12'H CHAMBER, THERMO PROCESSOR, RATED AT 1 MILLION BTU/HR, 900 POUNDS/HR DISCHARGE CAPACITY. UNIT LAST RUN AS CERAMICBOND PROCESSOR ON CLAY AND HEAVY METALS WASTE MATERIAL. VERTICAL KILN IS TOP FED, COMPLETE WITH COMBUSTI... Learn More

LAB MILL, PERTEN, HAMMER TYPE CYCLONE MILL, INCLUDES A 2" DIAMETER FEED, WITH A THREE PIN GRINDING WHEEL. COMPLETE WITH 3/4" DIAMETER TOP RIGHT DISCHARGE, CARBON STEEL CONSTRUCTION. SERIAL # 010-209, 115 VOLT, 11 AMP 3240 RPM SINGLE PHASE THE TYPE 3100, 6... Learn More

MILL, GRINDER, GRIFFITH LABS MINCE MASTER, SERIAL NO. CR20551, MACHINE NO. SWU5986. STAINLESS STEEL CONTACTS WITH 8" DIA. GRINDING CHAMBER AND 5" DIAMETER CENTER CORE WITH (2) CUTTING KNIVES. SCREEN DISCHARGE IS CIRCULAR APPROX. 1-1/2" WIDE WITH 1/20" DIA... Learn More

(2) CUMBERLAND MODEL 26 PELLETIZER, WITH MILLING TYPE ROTOR, 27" WIDE, 60 BLADES. UNIT DESIGNED TO CUT TO LENGTH MULTIPLE EXTRUDER PLASTIC STRANDS, .125" TO .092" DIAMETER, UP TO 10,000#/HR CAPACITY. UNIT HAS 40 HP DC DRIVE, COMPLETE WITH ELECTRICALS WITH... Learn More

FOREMOST PLASTIC GRANULATOR/ GRINDER. UNIT IS MODEL HD-6 WITH CARBON STEEL CONTACT PARTS, COMPLETE WITH 15 HP MOTOR DRIVE, 440 VOLT. UNIT FEATURES 18" DIAMETER X 15" WIDE GRINDING CHAMBER, WITH INLET AT 14" FRONT TO BACK, 15" LEFT TO RIGHT. MILL DESIGNED ... Learn More

FOREMOST PLASTIC GRANULATOR/ GRINDER. UNIT IS MODEL HD-6 WITH CARBON STEEL CONTACT PARTS, COMPLETE WITH 15 HP MOTOR DRIVE, 440 VOLT. UNIT FEATURES 18" DIAMETER X 15" WIDE GRINDING CHAMBER, WITH INLET AT 14" FRONT TO BACK, 15" LEFT TO RIGHT. MILL DESIGNED ... Learn More

ALSTEELE PLASTIC SCRAP GRINDER MODEL 7X18. UNIT DRIVEN BY 30 HP DIRECT DRIVE, 1170 RPM, 220/440V DRIVE MOTOR. CHAMBER IS 7" DIA x 18" WIDE WITH SCREEN DISCHARGE, 6" x 18" FEED CHUTE. COMPLETE MILL IS JACKETED FOR WATER COOLING. UNIT COMPLETE, MOUNTED ON H... Learn More

GRINDING MILL, MFG BY PALLMANN, MDL PS4-2-1/2 W/5 ROTATING BLADES AND ONE STATIONARY BLADE. UNIT HAS STAINLESS STEEL CONTACT PARTS. BLADES MEASURE 3-1/2" x 10"L IN A 10" x 21" DIA GRINDING CHAMBER. UNIT DRIVEN BY 10 HP, 230/460 V-BELT VOLT DRIVE. MOUNTED ... Learn More

SUGAR GRINDING SYSTEM, CONSISTS OF POWDER MILLING AND MIXING SECTION. SYSTEM INCLUDES FEED HOPPER WITH ROTARY VALVE TO FEED SUGAR INTO MILLING SECTION, CONSISTING OF HERMANN BAUERMEISTER UNIVERSAL MILL, TYPE UZU11, RATED FOR 5200 RPM, DRIVEN BY APPROX 10 ... Learn More

AIR HEATER, STERLING MDL M2B, 400 MILLION BTU/HR GAS FIRED SPACE HEATER, DESIGNED TO PRODUCE UP TO 8500 CFM WARM AIR @3.5" PRESSURE. OUTDOOR INSTALLATION TYPE. HAS 1-1/2 HP BLOWER. 1995. ... Learn More

(2) HOPPER, APPROXIMATELY 40 CU. FT. CAPACITY, VERTICAL ORIENTATION, STAINLESS STEEL CONSTRUCTION, MEASURES 24" WIDE X 24" LONG X 120" STRAIGHT SIDE, CONE TOP AND CONE BOTTOM WITH 10" DIAMETER BOTTOM SIDE BOTTOM MOUNTED SIGHT GLASS/ACCESS DOOR. HOPPER INC... Learn More

MILL, RUBBER, 2 ROLL, BOLLING, 6" x 12", 7.5 HP, 220/440 VOLT, CHAIN SPROCKET DRIVE. UNIT HAS REBUILT/NEW BRONZE BUSHINGS, LESS ROTARY VALVES AND APRON.... Learn More

MILL, RUBBER, FARREL, 2 ROLL, 6" X 12", COMPLETE WITH CORD ROLLS, CARBON STEEL DESIGN. UNIT DRIVEN BY 10 HP, 230/460 VOLT V-BELT DRIVE TO JACK SHAFT TO PINION BULL GEAR DRIVE. FARREL MILLS BEARS S/N 8841, UNITIZED ON BASE. UNIT IS MANUAL ROLL SET, IN FAIR... Learn More

LEHMAN 2 ROLL MILL, FLAKING/CRACKING TYPE, 12" DIAMETER X 12" FACE, EQUIPPED WITH A 15 HP, GEAR HEAD, CHAIN TO SPROCKET DRIVE, ROLLS ARE CORED FOR STEAM, FOR VEGETABLE OIL SEED AND GRAIN APPLICATION. S/N 1338.... Learn More

J.H. DAY 3-ROLL MILL SIZE 10" X 22". UNIT COMPLETE WITH 10/5 HP 2 SPEED 440 VOLT DRIVE. MILL HAS MANUAL ROLL SET IS COMPLETE LESS GUIDES AND APRON. ROLLS ARE IN EXCELLENT CONDITION, NEVER BEEN REGROUND. SERIAL NUMBER 42651.... Learn More

MILL, ROLL, KENT, 3-3/4" X 8", 3 ROLL, MANUAL ADJUSTMENT, WATER COOLED, LESS MOTOR.... Learn More

ROSS 3 ROLL MILL WITH 6" X 14" WATER COOLED ROLLS. UNIT COMPLETE WITH 2 SPEED 5/2.5 HP, 440 VOLT EXP MOTOR DRIVE. UNIT FEATURES MANUAL ROLL SETS WITH DIAL INDICATORS AND HYDRAULIC APRON ADJUSTMENT. ROLLS ARE IN GOOD CONDITION, COMPLETE WITH DISCHARG APRON... Learn More

ALLIS-CHALMERS CRACKING MILL, CONSISTS OF 4 ROLLS, (2) ON TOP OF (2). 9" DIAMETER X 24" WIDE SMOOTH FACE ROLLS FOR LUMP BREAKING OR GRANULATING SOFT MATERIAL. LAST USED ON BAUXITE ORE, CAN BE USED ON GRAINS OR OTHER MATERIALS. S/N 27296.... Learn More

SUGAR GRINDING SYSTEM, CONSISTS OF POWDER MILLING AND MIXING SECTION. SYSTEM INCLUDES FEED HOPPER WITH ROTARY VALVE TO FEED SUGAR INTO MILLING SECTION, CONSISTING OF HERMANN BAUERMEISTER UNIVERSAL MILL, TYPE UZU11, RATED FOR 5200 RPM, DRIVEN BY APPROX 10 ... Learn More

ATTRITION MILL, 22" DIAMETER, CARBON STEEL CONSTRUCTION, DRIVEN BY 30 HP MOTOR. APPEARS TO BE IN GOOD CONDITION.... Learn More

ATTRITION MILL, MANUFACTURED BY PRATER/BAUERMEISTER, MODEL UT-42USCH, DRIVEN BY 75 HP MOTOR. SERIAL NUMBER 102520/10277. APPEARS TO BE IN GOOD CONDITION. INCLUDES 30" DIAMETER ROTOR WITH 7" WIDE X 1" THICK MILLING BLADES ON 1" SPACINGS, CARBON STEEL CONST... Learn More

REPLACEMENT OR SPARE PRESSURE BOWL FOR SZEGVARI BATCH TYPE ATTRITOR MILL. UNIT FITS SZEGVARI SIZE 1S MILL AND FEATURES STAINLESS STEEL CONTACT PARTS, JACKET FOR COOLING AND CAPABILITY FOR PRESSURIZED SERVICE TO 15 PSI. BOWL IS IN EXCELLENT CONDITION.... Learn More

SZEGVARI ATTRITOR MILL, SIZE 1S, BATCH TYPE WITH 1 GALLON CAPACITY. UNIT FEATURES URETHANE LINE ON BOWL, STAINLESS SHAFT AND CARBON STEEL AGITATOR. BOWL IS JACKETED FOR COOLING AND MEASURES 7" DIA x 8" DEEP WITH PLASTIC COVER. UNIT IS DRIVEN BY 2 HP, 230/... Learn More

ATTRITOR MILL, MANUFACTURED BY UNION PROCESS, MODEL# Q-100, COMPLETE WITH STAINLESS STEEL, JACKETED TANK. COMPLETE WITH MAIN DRIVE. REPORTED TO BE IN VERY GOOD CONDITION.... Learn More

ATTRITOR MILL, INTERMITTENT TYPE ATTRITOR, MANUFACTURED BY UNION PROCESS, SIZE 1S, TYPE B, COMPLETE WITH STAINLESS STEEL, JACKETED TANK. TANK MEASURES 8" DIAMETER X 8" DEEP, INCLUDES S/ST AGITATOR WITH PADDLES. COMPLETE WITH 1/2 HP, 220/440 VOLT, 3/60HZ M... Learn More

ATTRITOR MILL, INTERMITTENT TYPE ATTRITOR, MANUFACTURED BY UNION PROCESS, SIZE 1S, TYPE B, COMPLETE WITH STAINLESS STEEL, JACKETED TANK. TANK MEASURES 5" DIAMETER X 6" DEEP, INCLUDES S/ST AGITATOR WITH PADDLES. COMPLETE WITH 3/4 HP, DC DRIVE THRU GEARBOX ... Learn More

ATTRITOR MILL, MANUFACTURED BY UNION PROCESS, SIZE 60-S, COMPLETE WITH STAINLESS STEEL, JACKETED TANK WITH CERAMIC LINING. TANK MEASURES 29" DIAMETER X 29" DEEP, 2-1/4" SIDE BTM. OUTLET. INCLUDES AGITATOR WITH 2-1/4" DIA. SHAFT AND (7) SETS OF RUBBER-LINE... Learn More

BALL MILL, 10'DIAMETER (3.05M) X 10'LONG (3.05M), WET OVERFLOW DISCHARGE, SERIAL NUMBER M4-371, MFG BY KURIMOTO IRON WORKS LTD, 1969. RATED AT 1020 TON PER DAY CAPCITY, COMPLETE WITH 370 kW INDUCTION MOTOR, 3 PHASE, 60 CYCLE, 460 VOLTS, 1190 RPM THROUGH S... Learn More

DOMINION ENGINEERING BALL MILL, 10' X 15'. COMPLETE WITH GENERAL ELECTRIC 1000 HP, SYNCHRONOUS, 460 VOLT, 60 HZ, 3 PH, 224 RPM MOTOR. RUBBER LINERS INSTALLED. ONE PIECE SHELL, 320-TOOTH GIRTH GEAR, 30-TOOTH PINION, 25" WIDE DOUBLE HELICAL GEAR.
... Learn More

ALLIS CHALMERS BALL MILL, 10'DIAMETER(3082 MM) X 18'LONG(5486 MM), WET OVERFLOW TYPE, SERIAL #C2482. COMPLETE WITH BULL GEAR AND PINION DRIVE THROUGH SPEED REDUCER. MOTOR NO LONGER AVAILABLE LAST USED 800 HP. NO LINERS. S/N C2482. CONDITION GOOD.... Learn More

(3) NORDBERG BALL MILLS, 13' DIAMETER X 18'-8" LONG. SINGLE COMPARTMENT, WET, OVERFLOW DISCHARGE, LAST USED AS A ROD MILL BUT IDENTICAL TO BALL MILL DESIGN. COMPLETE WITH 1500 HP WESTINGHOUSE, 3 PHASE, 4000V, MODEL HR-8G, SYNCRONOUS MOTOR THROUGH FAWICK M... Learn More

(2) DOMINION BALL MILLS, 13.5' X 22'8". COMPLETE WITH GENERAL ELECTRIC 2750 HP, SYNCHRONOUS MOTOR, MODEL 114494, TYPE TS, 4000 VOLTS, 180 RPM, 3 PH, 60 HZ, DOUBLE HELICAL 386T GEAR, 34T PINION, 30" FACE WIDTH, 20 DEGREE PRESSURE ANGLE, 80" X 30" TRUNNION ... Learn More

DENVER BALL MILL, 3' DIAMETER X 5' LONG. COMPLETE WITH 20 HP, 3PH, 60HZ, 220/440V, ELECTRIC MOTOR THROUGH GEAR REDUCER, PINION AND TWO PIECE RING GEAR. ACCESSORIES INCLUDE AIR/ELECTRIC AUTO LUBRICATION SYSTEM WITH BARREL PUMP, FEED AND DISCHARGE CHUTES. L... Learn More

DENVER BALL MILL, 3' DIA X 6' LONG. UNIT SHOWS NO SIGNS OF EXTERNAL SHELL OR HEAD DAMAGE. DISCHARGE TROMMEL IN VERY GOOD CONDITION, STEEL LINERS SHOW VERY LITTLE WEAR. GIRTH GEAR AND PINION IN GOOD CONDITION. SKID MOUNTED. VERY GOOD CONDITION.... Learn More

ALLIS CHALMERS SAG MILL, 7' X 3'. COMPLETE WITH SIEMENS-ALLIS 40 HP DRIVE MOTOR, 1765 RPM, TYPE RGZ, 97.2/48.6 AMPS, 3 HP, 60 HZ, 230/460 VOLT. INCLUDES FALK GEAR REDUCER, MODEL 401-7E22-06A, M.O. NUMBER 7-931730, 82 RPM, 21.35:1 RATIO, 40 HP. CLASS 1 SHE... Learn More

MARCY 8' DIAMETER X 6' LONG BALL MILL WITH TRUNNION FEED AND DISCHARGE. RUBBER LINERS AND LIFTERS. LAST USED IN A WET GRIND APPLICATION. PREVIOUSLY DRIVEN BY 250 HP MOTOR THRU GEAR & PINION. GEARS GOOD. LOTS OF WEAR ON (1) OF THE TRUNNIONS. MILL S/N 700. ... Learn More

(2) HARDINGE CONICAL BALL MILL, 8' x 72" STRAIGHT SIDE, MINIMUM 220 HP, MAXIMUM 250 HP, MILL WEIGHT 37100 LB EACH, LINING WEIGHT 29000 LB EACH, MINIMUM BALL WEIGHT 44000 LB PER MILL, MAX BALL WIGHT 56500 LB PER MILL, MINIMUM RPM 18.2, MAXIMUM RPM 23.8.... Learn More

BALL MILL, 9'DIA (2745MM) X 15'LONG (4570MM), MFG BY KOBE-ALLIS. LAST USED AS REGRIND BALL MILLS IN COPPER CURCUIT, EACH COMPLETE WITH YASAKAWA 450 kW (603 HP) SYNCHRONOUS MOTORS, 3300 VOLTS, 60 CYCLES. RATE AT 35 METRIC TONS PER HOUR CAPACITY.... Learn More

BALL MILL, 9-1/2' DIAMETER X 13' LONG, MANUFACTURED BY MARCY, FORMERLY DRIVEN BY 600 HP MOTOR AND GEAR REDUCER (LESS DRIVE ASSEMBLY). FORMERLY USED STEEL LINERS. INCLUDES HERRINGBONE GEAR 332 TEETH, 19 TEETH PINION AND 22" FACE, BRONZE BEARING INSERTS FOR... Learn More

CANADIAN ALLIS CHALMERS 6' X 8 BALL MILL. SPARE PARTS AVAILABLE. BULL GEAR IS LIKE NEW; SHELL AND HEAD LINERS ARE INSTALLED. UNIT REQUIRES TRUNNION BEARINGS, PINION AND DRIVE ARRANGEMENT COMPLETE.... Learn More