Search results for: 'Ball Mill'

Search results for 'Ball Mill'

D733556

MILL, BALL, 10' X 10', KURIMOTO IRON WORKS, 370 kW,

BALL MILL, 10'DIAMETER (3.05M) X 10'LONG (3.05M), WET OVERFLOW DISCHARGE, SERIAL NUMBER M4-371, MFG BY KURIMOTO IRON WORKS LTD, 1969. RATED AT 1020 TON PER DAY CAPCITY, COMPLETE WITH 370 kW INDUCTION MOTOR, 3 PHASE, 60 CYCLE, 460 VOLTS, 1190 RPM THROUGH S... Learn More

D735555

MILL, BALL, 10' X 15', DOMINION ENGINEERING, 1000 HP, WET

DOMINION ENGINEERING BALL MILL, 10' X 15'. COMPLETE WITH GENERAL ELECTRIC 1000 HP, SYNCHRONOUS, 460 VOLT, 60 HZ, 3 PH, 224 RPM MOTOR. RUBBER LINERS INSTALLED. ONE PIECE SHELL, 320-TOOTH GIRTH GEAR, 30-TOOTH PINION, 25" WIDE DOUBLE HELICAL GEAR.
... Learn More

D733555

MILL, BALL, 10' X 18', ALLIS CHALMERS, 800 HP, WET OVERFLOW,

ALLIS CHALMERS BALL MILL, 10'DIAMETER(3082 MM) X 18'LONG(5486 MM), WET OVERFLOW TYPE, SERIAL #C2482. COMPLETE WITH BULL GEAR AND PINION DRIVE THROUGH SPEED REDUCER. MOTOR NO LONGER AVAILABLE LAST USED 800 HP. NO LINERS. S/N C2482. CONDITION GOOD.... Learn More

S735234

MILL, BALL, 13' X 18' 8", NORDBERG, 1500 HP, (3)

(3) NORDBERG BALL MILLS, 13' DIAMETER X 18'-8" LONG. SINGLE COMPARTMENT, WET, OVERFLOW DISCHARGE, LAST USED AS A ROD MILL BUT IDENTICAL TO BALL MILL DESIGN. COMPLETE WITH 1500 HP WESTINGHOUSE, 3 PHASE, 4000V, MODEL HR-8G, SYNCRONOUS MOTOR THROUGH FAWICK M... Learn More

D735556

MILL, BALL, 13.5' X 22.8', DOMINION ENGRG, 2750 HP, (2)

(2) DOMINION BALL MILLS, 13.5' X 22'8". COMPLETE WITH GENERAL ELECTRIC 2750 HP, SYNCHRONOUS MOTOR, MODEL 114494, TYPE TS, 4000 VOLTS, 180 RPM, 3 PH, 60 HZ, DOUBLE HELICAL 386T GEAR, 34T PINION, 30" FACE WIDTH, 20 DEGREE PRESSURE ANGLE, 80" X 30" TRUNNION ... Learn More

S734750

MILL, BALL, 3' X 5', DENVER, 25 HP, ON SKID

DENVER BALL MILL, 3' DIAMETER X 5' LONG. COMPLETE WITH 20 HP, 3PH, 60HZ, 220/440V, ELECTRIC MOTOR THROUGH GEAR REDUCER, PINION AND TWO PIECE RING GEAR. ACCESSORIES INCLUDE AIR/ELECTRIC AUTO LUBRICATION SYSTEM WITH BARREL PUMP, FEED AND DISCHARGE CHUTES. L... Learn More

D735554

MILL, BALL, 3' X 6', DENVER, DRY GRIND

DENVER BALL MILL, 3' DIA X 6' LONG. UNIT SHOWS NO SIGNS OF EXTERNAL SHELL OR HEAD DAMAGE. DISCHARGE TROMMEL IN VERY GOOD CONDITION, STEEL LINERS SHOW VERY LITTLE WEAR. GIRTH GEAR AND PINION IN GOOD CONDITION. SKID MOUNTED. VERY GOOD CONDITION.... Learn More

S484980

MILL, BALL, 8' X 6', MARCY, 250 HP, WET, RBR LINERS/LIFT,

MARCY 8' DIAMETER X 6' LONG BALL MILL WITH TRUNNION FEED AND DISCHARGE. RUBBER LINERS AND LIFTERS. LAST USED IN A WET GRIND APPLICATION. PREVIOUSLY DRIVEN BY 250 HP MOTOR THRU GEAR & PINION. GEARS GOOD. LOTS OF WEAR ON (1) OF THE TRUNNIONS. MILL S/N 700. ... Learn More

D733868

MILL, BALL, 8' x 72", HARDINGE, CONICAL,(2)

(2) HARDINGE CONICAL BALL MILL, 8' x 72" STRAIGHT SIDE, MINIMUM 220 HP, MAXIMUM 250 HP, MILL WEIGHT 37100 LB EACH, LINING WEIGHT 29000 LB EACH, MINIMUM BALL WEIGHT 44000 LB PER MILL, MAX BALL WIGHT 56500 LB PER MILL, MINIMUM RPM 18.2, MAXIMUM RPM 23.8.... Learn More

D733559

MILL, BALL, 9' X 15', 600 HP, KOBE-ALLIS CHALMERS, (1)

BALL MILL, 9'DIA (2745MM) X 15'LONG (4570MM), MFG BY KOBE-ALLIS. LAST USED AS REGRIND BALL MILLS IN COPPER CURCUIT, EACH COMPLETE WITH YASAKAWA 450 kW (603 HP) SYNCHRONOUS MOTORS, 3300 VOLTS, 60 CYCLES. RATE AT 35 METRIC TONS PER HOUR CAPACITY.... Learn More

D734871

MILL, BALL, 9-1/2' X 13', MARCY,

BALL MILL, 9-1/2' DIAMETER X 13' LONG, MANUFACTURED BY MARCY, FORMERLY DRIVEN BY 600 HP MOTOR AND GEAR REDUCER (LESS DRIVE ASSEMBLY). FORMERLY USED STEEL LINERS. INCLUDES HERRINGBONE GEAR 332 TEETH, 19 TEETH PINION AND 22" FACE, BRONZE BEARING INSERTS FOR... Learn More

D733948

MILL, BALL, ALLIS CHALMERS, 6' X 8',

CANADIAN ALLIS CHALMERS 6' X 8 BALL MILL. SPARE PARTS AVAILABLE. BULL GEAR IS LIKE NEW; SHELL AND HEAD LINERS ARE INSTALLED. UNIT REQUIRES TRUNNION BEARINGS, PINION AND DRIVE ARRANGEMENT COMPLETE.... Learn More

S731598

MILL, BALL, BATCH, 4' x 4-1/2', ABBE, C/ST, JKT, (2)

(2) ABBE BALL MILL, 4 x 4-1/2, CARBON STEEL, JACKETED FOR COOLING. MOTOR IS 25 HP, 220/440V, 1750 RPM, 63/31.5 AMP, TO NUTTAL GEARBOX 11.39:1 RATIO, 155 RPM OUTPUT, 22 TEETH. MILL TURNS @ 21 RPM. ... Learn More

Z496700

MILL, ROD, 10'8" X 15', MARCY, 1000 HP, 2300 VOLT, 60,

ROD MILL, 10'8" DIA X 15' LONG, MFG BY MARCY WITH A 1000 HP, 2300 VOLT, 60 CYCLE, 225 HP, A/C SYNCHRONOUS DRIVE MOTOR, 21 TOOTH PINION, AND 293 TOOTH HELICAL MASTER GEAR. 60" DIA. X 20" FACE TRUNNIONS, FARVAL LUBRICATION SYSTEM WITH HEATING AND COOLING CA... Learn More

C523490

MILL, VIBRATORY, 16" X 36", PALLA, 3 CHAMBER,

VIBRATING BALL MILL, 3 CHAMBERS MEASURING 16" DIA. X 36" LONG EACH, SIMILAR TO A PALLA DESIGN, ON A COMMON STAND. APPEARS TO BE UNUSED. ... Learn More

Can't find what you are looking for?

TOP REQUESTED CATEGORIES OF USED EQUIPMENT

Machinery & Equipment, Inc.
P.O. Box 7632, San Francisco, CA 94120

Phone: (415) 467-3400 Fax (415) 467-2639
San Francisco Toll Free (800) 227-4544
Los Angeles Toll Free (800) 870-9680

Used Food, Pharmaceutical, Chemical and Minerals Processing Equipment

You're currently on:

Category Navigation: